เครื่องชาร์จ CellPro PowerLab 6 คุณภาพสูงจาก USA ให้กำลังไฟชาร์จถึง 1000W. ชาร์จแบตเตอรี่ได้ถึง 40A.
ชุดนี้จัดชุดมาสำหรับการชาร์จแบตพ่วงกันได้ 2 แพ็ค
ในชุดประกอบด้วย
ตัวเครื่องชาร์จ สายชาร์จแบตฯ 2ชุด สายต่อบาล้านซ์ 2ชุด
ตัวเครื่องชาร์จสามารถพ่วงแบตชาร์จได้ถึง9pack สามารถจัดหาสายชาร์จแบต และสายบาลานซ์ชาร์จเพิ่มเติมได้
ถ้าต้องการทำโปรแกรมผ่านทางคอมพิวเตอร์สามารถจัดหาสาย USB interface ได้
ดาวน์โหลดคู่มือได้ ที่นี่
Combo Contents: 1 Cellpro PowerLab 6 EC5-equipped Battery Workstation, 2 red/black safety banana plug-to-bare wire cable, 2 CP8S-GP/KO6S-PAR Safe Parallel Adapters. Click here to view product specifications. Not sure which adapter you need? Click here for adapter compatibility.
This combo designed to support charging 2 same-cell-count packs in parallel, packs must be GP/KO compatible 2s-6s, one per adapter
*Note - the new PowerLab 6 with EC5-equipped input cable includes a one foot long, 12AWG input wire terminating with an EC5, female pin connector. Revolectrix also has an available 2 foot long plier clip assembly to support the new PowerLab 6. The available cable has the mating EC5 male pin connector-to-plier clips for connecting to a car battery or power supply. Look for this accessory further down on the store page of the web site.
Specification
For Battery types: Lithium Polymer (1s to 6s balanced, 1s to 2s unbalanced), Lithium Ion (1s to 6s balanced, 1s to 2s unbalanced), Lithium Manganese (1s to 6s balanced, 1s to 2s unbalanced), A123 (LiFePO4) (1s to 6s balanced, 1s to 8s unbalanced), NiCd (1s to 19s), NiMH (1s to 19s), 6v, 12v, 24v Lead Acid batteries (Flooded, Gel, AGM, SLA)
Pack capacity: 20 mAh to 360Ah
Input voltage: 10-32VDC, reverse polarity protected
Input current: 1A to 40A, software limited
Power conversion: Synchronous DC/DC converter, supports multiple switcher frequencies of 31.25 kHz, 62.5 kHz, 125 kHz; user selectable by preset, 85% to 93% efficiency depending on output current
Output battery charge current: Adjustable range 10mA to 40A, limited by 40A input current*
Output battery discharge current: Internal discharge 10mA to 8A, 50W max Regenerative discharge 10mA to 40A, 1000W max**
Continuous max output power: 408W @ +12VDC input, 1000W @ +30VDC
Cell balancing: Resolution 78uV (16 bit) for 1s-8s Li or A123 (LiFePO4) balanced charging
Voltage calibration: Cell voltage measurements are factory calibrated to a standard traceable to NIST; calibration is to +/- 6 mV
Current calibration: Charge current is factory calibrated on a 4A standard; calibration is to +/- 1mA
Measurement accuracy: Voltage resolution: 78uV (16 bit) Voltage tolerance: +/- 6mV Charge current: +/- 1% Capacity added to pack: +/- 1% Percent capacity (Fuel): +/- 5% (with accurate fuel table defined for battery being charged)
Serial data output: 19.2kbps, 8 bits, 1 start bit, 1 stop bit, no parity
Data integrity: Checksum, CRC checking
Cooling fans: Single, 13 CFM, 50mm diameter
Heat sink: Internal 120W aluminum, thin finned
Output battery connector: Cellpro compatible, JST PA series, 9 position
LCD: 2 line, 16 character, light grey/blue backlit
Size: 5.70" x 5.57" x 3.40"
Footnotes:
* Please note, for safety reasons, available charger current may be limited for certain battery types and/or charging modes, e.g., non-balanced charge of Li
** Please check bullet number 9 in the section titled Major Features (Features tab) for a detailed description of Regenerative Discharge
201254 |