เครื่องชาร์จแบตเตอรี่ Cellpro PowerLab 6 คุณภาพสูงจาก USA
ให้กำลังไฟถึง 1000W ชาร์จแบตฯได้สูงสุดถึง 40A. และ dischargeได้สูงสุดถึง 8A
ชุดนี้มีเฉพาะเครื่องชาร์จ สามารถจัดหาสายชาร์จแบต และสายชาร์จบาลานซ์ได้ ตัวเครื่องชาร์จสามารถต่อพ่วงแบตได้ถึง 9 pack จัดหาสายชาร์ตบาลานซ์ต่อพ่วงได้
ดาวน์โหลดคู่มือได้ ที่นี่
For Battery types: Lithium Polymer (1s to 6s balanced, 1s to 2s unbalanced), Lithium Ion (1s to 6s balanced, 1s to 2s unbalanced), Lithium Manganese (1s to 6s balanced, 1s to 2s unbalanced), A123 (LiFePO4) (1s to 6s balanced, 1s to 8s unbalanced), NiCd (1s to 19s), NiMH (1s to 19s), 6v, 12v, 24v Lead Acid batteries (Flooded, Gel, AGM, SLA)
Pack capacity: 20 mAh to 360Ah
Input voltage: 10-32VDC, reverse polarity protected
Input current: 1A to 40A, software limited
Power conversion: Synchronous DC/DC converter, supports multiple switcher frequencies of 31.25 kHz, 62.5 kHz, 125 kHz; user selectable by preset, 85% to 93% efficiency depending on output current
Output battery charge current: Adjustable range 10mA to 40A, limited by 40A input current*
Output battery discharge current: Internal discharge 10mA to 8A, 50W max Regenerative discharge 10mA to 40A, 1000W max**
Continuous max output power: 408W @ +12VDC input, 1000W @ +30VDC
Cell balancing: Resolution 78uV (16 bit) for 1s-8s Li or A123 (LiFePO4) balanced charging
Voltage calibration: Cell voltage measurements are factory calibrated to a standard traceable to NIST; calibration is to +/- 6 mV
Current calibration: Charge current is factory calibrated on a 4A standard; calibration is to +/- 1mA
Measurement accuracy:
Voltage resolution: 78uV (16 bit)
Voltage tolerance: +/- 6mV
Charge current: +/- 1%
Capacity added to pack: +/- 1%
Percent capacity (Fuel): +/- 5% (with accurate fuel table defined for battery being charged)
Serial data output: 19.2kbps, 8 bits, 1 start bit, 1 stop bit, no parity
Data integrity: Checksum, CRC checking
Cooling fans: Single, 13 CFM, 50mm diameter
Heat sink: Internal 120W aluminum, thin finned
Output battery connector: Cellpro compatible, JST PA series, 9 position
LCD: 2 line, 16 character, light grey/blue backlit
Size: 5.70" x 5.57" x 3.40"
Footnotes:
* Please note, for safety reasons, available charger current may be limited for certain battery types and/or charging modes, e.g., non-balanced charge of Li
** Please check bullet number 9 in the section titled Major Features (Features tab) for a detailed description of Regenerative Discharge
ALL NEW! 1000W Battery Workstation including an EC5 input cable, will charge, discharge, monitor, or multiple cycle any current or future battery chemistry. POWER you have been waiting for, safety you have come to expect in a compact, affordable Cellpro product. Welcome to the new class of R/C battery management. Built on the amazing PowerLab 8 technology, designed from the ground up for reliable high power, geared toward the power user but simple to operate and affordable enough for the masses. The extensive list of features and capabilities are rivaled only by the goal to provide the ultimate in flexibility and utility. Out of the box, the PL6 will run circles around the competition in terms of simple, yet powerful set up and operation. But if you are the type of person looking for the utmost in flexibility and performance, look no further. The PL6, in combination with the Charge Control Software offer virtually unlimited access to charging parameters. Inside the Windows environment, it's easy to alter up to 100 settings for any of the 25 user presets, gain access to 50 additional library presets in the unit or tap into the PC library. Major features include Advanced Power Management to help you set up and use existing Power Supplies or Pb input batteries, faster individual cell IR readout, support for all new Safe Parallel Adapters (PL6 and PL8 share the same adapters) which enable charging/discharging multiple packs simultaneously, Expansion Channel Mode for turning multiple PL6's into one workstation, regenerative discharge with input power supply protection built in. The new PowerLab 6 with EC5-equipped input cable includes a one foot long, 12AWG input wire terminating with an EC5, female pin connector. Revolectrix also has an available 2 foot long plier clip assembly to support quick inter-connect to the input power source. The available cable has the mating EC5 male pin connector-to-plier clips for connecting to a car battery or power supply. Look for this accessory further down on the store page of the web site.Click here to view product specifications and download Charge Control Software to your PC.
[541118] |
